The Basics of Plumbing Knowledge for Bathtub Installation
The Basics of Plumbing Knowledge for Bathtub Installation
Blog Article
Just about every person may have their personal conception in relation to Installing A Bathtub.
Setting up a bath tub isn't exactly rocket science, but it does require solid plumbing, woodworking, as well as in some cases, tiling abilities. Changing an old tub with a brand-new one is additionally a moderately hard project. If the old bathtub is readily accessible, the task can move rapidly; if you have to open up a wall to eliminate the old tub as well as place the new bath tub, the task is much harder. In either situation, the job is within a home handyman's skills, although you will need a helper to vacate the old tub and also embeded in the new one. Make sure you have actually certified yourself for the task as well as fit attempting it. Instead of working with a professional to take control of a halfway-completed project, it is better to take into consideration using one prior to you begin. Opportunities are you might require a specialist plumber to make tube connections.
This post will certainly assist you mount a brand-new bathtub in your shower room if you have actually currently acquired a new tub as well as do not need to alter the setup of your previous water pipelines.
Your tools as well as product checklist should comprise the following:
Getting ready for the Installation
Firstly, the supporting framework supplied with the bath must be fitted (if needed) according to the manufacturer's instructions. Next off, fit the faucets or mixer to the tub. When suitable the faucet block, it is important to make sure that if the faucet features a plastic washing machine, it is fitted between the bath as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of the two faucets utilizing 2 nuts and olives (often provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet with the hole in the bathroom. Make use of the nut provided by the producer to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Make certain you make use of every one of the supplied washers.
Connect the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be suited its last setting.
Removing Old Touches
If you require to change old taps with new ones as a part of your installation, then the first thing you ought to do is detach the supply of water. After doing so, switch on the taps to drain any water staying in the system. The process of eliminating the existing faucets can be fairly bothersome due to the limited gain access to that is usually the case.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the faucets. Have a fabric prepared for the remaining water that will certainly originate from the pipelines. As soon as the supply pipelines have actually been removed, use the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will have to be cleansed of any old sealing compound.
Prior to proceeding to fit the brand-new faucets, compare the pipeline connections on the old faucets to the brand-new taps. If the old faucets are longer than the brand-new taps, then a shank adapter is needed for the new taps to fit.
Installing the Tub
Making use of the two wooden boards under its feet, position the bathtub in the needed placement. The wooden boards are handy in evenly spreading the weight of the bathtub over the location of the boards as opposed to concentrating all the weight onto four little factors.
The next goal is to make sure that the tub is leveled all round. This can be attained by checking the spirit level and also readjusting the feet on the tub till the spirit level reviews degree.
To set up faucets, fit all-time low of the outermost flexible tap connector to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Activate the water system as well as inspect all joints and also new pipework for leaks and also tighten them if required. Fill the bath tub as well as additionally inspect the overflow outlet and the typical electrical outlet for leakages.
Lastly, take care of the bath paneling as explained in the supplier's user's manual. Tiling and securing around the bathtub must wait till the bath tub has actually been utilized at least when as this will settle it right into its last setting.
Suitable New Taps
If the tails of the new taps are plastic, then you will require a plastic port to avoid damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end supplies a link to the existent supply pipes.
If you require to fit a monobloc, after that you will certainly call for reducing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipeline.
Next, place the tap in the mounting opening in the bath/basin ensuring that the washing machines remain in area between the faucet and also the sink. Secure the faucet in position with the maker supplied backnut. When the tap is securely in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with typical faucet connectors. The former kind ought to be linked to the tap finishes first, tightening only by hand. The supply pipelines can later on be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the location where the bathroom satisfies the tile, it is required to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a stiff seal, creating the water to penetrate the wall between the bath and also the tiling, bring about difficulties with wetness and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, and are capable of securing gaps approximately a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with spins of drenched newspaper or soft rope. Bear in mind to constantly fill the bath tub with water before securing, to permit the movement experienced when the tub is in use. The sealant can break fairly very early if you do not think about this activity before sealing.
Alternatively, ceramic coving or quadrant tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily readily available on the marketplace. It is recommended to fit the floor tiles making use of waterproof or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a serious reader about Tools You Need to Install a New Bathtub , I imagined sharing that blog post was sensible. Do you know about anybody else who is inquisitive about the subject? Do not hesitate to promote it. Many thanks for taking the time to read it.
Fix today, not tomorrow! Report this page